Ammco 927581 Mounting Hardware for the On the Car Lathe Bedienungsanleitung PDF herunterladen

Installation of the Storage Rack

Note: Use ﬁg. 1 and the parts list to accomplish

steps 1 through 4. The numbers in parentheses rep-

resent the item number of the parts in the parts list.

1. Hang the storage rack (2) inside the lathe storage

chest.

2. Fully insert the screw (3), into the storage rack

(2), to secure the rack to the storage chest (1).

3. Place the mounting bolts (10) in the two circular

holes on the left end of the storage rack (2).

4. From left to right, the following parts should be

loaded on the storage rack (2) by pushing the parts

over the tongues on the rack: ﬂat washers (9) and 1/8”

ﬂat spacers (12), nut plates (11), 1/8” spacers (8), 1/4”

spacers (7), 1/2” spacers (6), 1” spacers (5), and 2”

spacers (4).

PART

ITEM NO. QTY DESCRIPTION

2 27579 1 Storage Rack

3 28220 1 Round Head Screw

4 27089-05 2 2” Spacers

5 27089-04 2 1” Spacers

6 27089-03 2 1/2” Spacers

7 27089-02 2 1/4” Spacers

8 27089-01 2 1/8” Spacers

9 27212 2 Flat Washers

10 27086-03 2 Mounting Bolts

11 27580 2 Nut Plates

12 29517 2 1/8” Spacers, Flat

13 27077 1 Wrench

Use of Mounting Hardware

1. The lathe mounting hardware was designed for

use on vehicles with a pressed hub/knuckle/rotor

assembly or where removal of the rotor is difﬁcult or

inefﬁcient.

2. The vehicle’s caliper bolts can be used to mount

the lathe if the holes in the steering knuckle or caliper

mounting bracket are threaded and on the inboard

side of the rotor, ﬁg. 2. Also, the vehicle’s caliper bolts

should be 1-1/2” in length or longer. Otherwise, the

mounting bolts and nut plates provided in the hard-

ware package will be needed.

3. Whether you are mounting the lathe with the

vehicle caliper bolts or with the mounting bolts pro-

vided in the hardware kit, various combinations of

spacers may be required to take up the space

between the bolt heads and the lathe mounting

bracket to keep the bolt from interfacing with the

rotor.

Note: When using more than one spacer, care

should be taken to use the tongue and groove conﬁg-

uration to prevent misalignment, ﬁg. 3. If the small

1/8” spacer is required, it should be placed on the

caliper bolt last since it does not have the counter-bore

the other spacers possess.

AMMCO Tools, Inc. • Hennessy Industries • P.O. Box 3002, 1601 J.P. Hennessy Drive, LaVergne, TN 37086-1982

(800) 688-6359 • (615) 641-7533 • (615) 641-5104 FAX

Mounting Hardware for the

On the Car Lathe

—Installation Instructions with Parts Identiﬁcation—

No. 27581

Figure 1

Figure 2

Inboard Side

(toward

vehicle)

Outboard

Side (away

from vehicle)

Inboard Caliper

Mounting Bracket

Caliper Bolt (1-1/2”

Min. Length)

1 2 3 4

Inhaltsverzeichnis

Seite 1 - No. 27581

Installation of the Storage RackNote: Use ﬁg. 1 and the parts list to accomplishsteps 1 through 4. The numbers in parentheses rep-resent the item numb

Seite 2 - Caliper Bolts

4. The spacers may also be used to achieve theproper lathe position on the rotor, by placing the spac-ers on the caliper/mounting bolts between the la

Seite 3 - Supplied in Mounting Hardware

1. Place a washer on the caliper bolt.2. Place spacer(s), as required, onto the caliper bolt.3. Insert the caliper bolt with spacers and washerinto th

Seite 4

Kommentare zu diesen Handbüchern

Keine Kommentare

Ammco 927581 Mounting Hardware for the On the Car Lathe Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Ausrüstung Ammco 927581 Mounting Hardware for the On the Car Lathe herunter. AMMCO 927581 Mounting Hardware for the On the Car Lathe User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ausrüstung Ammco 927581 Mounting Hardware for the On the Car Lathe